71M6543F/71M6543G Data Sheet
4.5.3
Temperature Coefficients for the 71M6xx3
Refer to the 71M6xxx Data sheet for the equations that are applicable to each 71M6xx3 part number and
the corresponding temperature coefficients.
4.5.4
Temperature Compensation for VREF and Shunt Sensors
10 ? TEMP _ X ? PPMC 100 ? TEMP _ X 2 ? PPMC 2
2 14
2 23
the sample in each corresponding sensor channel. A GAIN_ADJx value of 16,384 (i.e., 2 )corresponds to
In the above equation, TEMP_X is the deviation from nominal or calibration temperature expressed in
multiples of 0.1 °C. The 10x and 100x factors seen in the above equation are due to 0.1 C scaling of
TEMP_X . For example, if the calibration (reference) temperature is 22 C and the measured temperature
is 27 C, then 10* TEMP_X = (27-22) x 10 = 50 (decimal), which represents a +5 C deviation from 22 C.
This section discusses metrology temperature compensation for the meter designs where current shunt
sensors are used in conjunction with the 71M6xx3 remote isolated sensors, as shown in Figure 31.
Sensors that are directly connected to the 71M6543 are affected by the voltage variation in the 71M6543
VREF due to temperature. On the other hand, shunt sensors that are connected to 71M6xx3 remote
sensor are affected by the VREF in the 71M6xx3. The VREF in both the 71M6543 and 71M6xx3 can be
compensated digitally using a second-order polynomial function of temperature. The 71M6543 and
71M6xx3 feature temperature sensors for the purposes of temperature compensating their corresponding
VREF. The compensation computations must be implemented in MPU firmware.
Referring to Figure 31 , the VADC8 (VA), VADC9 (VB) and VADC10 (VC) voltage sensors are always
directly connected to the 71M6543. Thus, the precision of the voltage sensors is primarily affected by
VREF in the 71M6543. The temperature coefficient of the resistors used to implement the voltage dividers
for the voltage sensors (see Figure 27 ) determine the behavior of the voltage division ratio with respect to
temperature. It is recommended to use resistors with low temperature coefficients, while forming the entire
voltage divider using resistors belonging to the same technology family, in order to minimize the temperature
dependency of the voltage division ratio. The resistors must also have suitable voltage ratings.
The 71M6543 also may have one local current shunt sensor that is connected directly to it via the IADC0-
IADC1 input pins, and therefore this local current sensor is also affected by the VREF in the 71M6543.
The shunt current sensor resistance has a temperature dependency, which also may require
compensation, depending on the required accuracy class.
The IADC2-IADC3, IADC4-IADC5 and IADC6-IADC7 current sensors are isolated by the 71M6xx3 and
depend on the VREF of the 71M6xx3, plus the variation of the corresponding remote shunt current sensor
with temperature.
The MPU has the responsibility of computing the necessary sample gain compensation values required for
each sensor channel based on the sensed temperature. Maxim provides demonstration code that
implements the GAIN_ADJx compensation equation shown below. The resulting GAIN_ADJx values are
stored by the MPU in five CE RAM locations GAIN_ADJ0-GAIN_ADJ5 ( CE RAM 0x40-0x44 ). The
demonstration code thus provides a suitable implementation of temperature compensation, but other
methods are possible in MPU firmware by utilizing the on-chip temperature sensors while storing the
sample gain adjustment results in the CE RAM GAIN_ADJx storage locations for use by the CE. The
demonstration code maintains five separate sets of PPMC and PPMC2 coefficients and computes five
separate GAIN_ADJx values based on the sensed temperature using the equation below:
GAIN _ ADJx = 16385 + +
The GAIN_ADJx values stored by the MPU in CE RAM are used by the CE to gain adjust (i.e., multiply)
14
unity gain, while values less than 16,384 attenuate the samples and values greater than 16,384 amplify
the samples.
o
o
o o o
In the demonstration code, TEMP_X is calculated in the MPU from the STEMP[10:0] temperature sensor
reading using the equation provided below and is scaled in 0.1°C units. See 2.5.5 71M6543 Temperature
Sensor on page 53 for the equation to calculate temperature in degrees °C from the STEMP[10:0] value.
Table 66 shows the five GAIN_ADJx equation output storage locations and the voltage or current sensor
channels for which they compensate for the 1 Local / 3 Remote configuration shown in Figure 31 .
v2
89
相关PDF资料
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200 CBL DSUB HD 15FEMAL-15MALE 2.0M
相关代理商/技术参数
71M6543F-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6543FT-IGT/F 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
71M6543GHT-IGT/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk
71M6543GHT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel
71M6543G-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel